[Fuxtec FX-RB144] Vorschläge Firmware Verbesserungen

  • Servus.

    Ich wollte das 1.1.6 aufspielen über wlan.

    Bei beiden (A als auch B) failed das Update immer. Hatte das auch schon mal jemand? Vorgegangen bin ich wie hier beschrieben!


    Grüße

  • Hy everyone.


    My name is Ivan, I am from Croatia and I own Fuxtec Mähroboter.

    I understand German pretty good, but I don't write in German as fluid as in English so if anybody understands and can reply to me (can be in German also) I would appreciate it very much.

    My problem with Fux is that sometimes it happens that when I start with Auto mode it starts from loadin station, turns for 180 as it would start to mow and then it goes crazy and turns in circles until it hits something. On display is "wire signal lost" error.

    I had same problem on 1.1 firmware and when I upgraded to 1.1.3 it was fine for apx 2 weeks until yesterday. Then I upgraded to 1.1.6 today and still the same problem. It doesn't go home when I push home button on display and also on mobile app when I give home command it doesn't react.

    But when I putt it in the middle of my yard and pres Auto mode it runs perfect until it is battery empty and it has to go for recharge. Then again the same problem, it finds the first virtual line and turns 360 like crazy! 😔

    I would appreciate any help.


    Lijepi pozdrav iz Hrvatske 😉

    Ivan.

  • turns in circles

    Tried to switch the connection of the cable on the back of the station?

    Spinning seems to happen if it's connected the wrong direction.

    Xiaomi Mi Robot Vacuum seit 04/2018 (FW: 3.5.0_003476)

    Xiaomi Mi Home Sicherheitskamera 360° 1080p (FW: 3.5.1_0217)

    Fuxtec FB144 seit 04/2019 (FW: Fuxtec 1.2-6)

  • Nothing ! When i switched connection on power station it doesn't even go to the line it starts to turn 360 immediately....

  • Try to install the original firmware of Fuxtec 1.2-6 , see Thread # 50.

    It works fine with my Fux ...

    Wenn das nicht geht versuch mal was anderes, vielleicht geht das ja auch nicht :/

  • Try to install the original firmware of Fuxtec 1.2-6 , see Thread # 50.

    It works fine with my Fux ...

    Ok, I will try.

    Do I have to do it like described (opening the mower) or can I do it through WIFI update tool?

  • with mine it worked via wifi

    Xiaomi Mi Robot Vacuum seit 04/2018 (FW: 3.5.0_003476)

    Xiaomi Mi Home Sicherheitskamera 360° 1080p (FW: 3.5.1_0217)

    Fuxtec FB144 seit 04/2019 (FW: Fuxtec 1.2-6)

  • i have tried with 1.2-6 also and I have the same problem ;(

    Is there maybe a problem with the "home address"? As I said before, it runs normally until it has to go to charging or out again :/

    There is a symbol on the display that it is paired with charging station.

  • Tried factory reset?

    Xiaomi Mi Robot Vacuum seit 04/2018 (FW: 3.5.0_003476)

    Xiaomi Mi Home Sicherheitskamera 360° 1080p (FW: 3.5.1_0217)

    Fuxtec FB144 seit 04/2019 (FW: Fuxtec 1.2-6)

  • manual section 5.9: initial setting

    restore to factory setting

    - select "set" and enter it by pressing green enter key

    - select "function" and enter it by pressing enter key

    - select "initial" and enter it by pressing enter key

    - select "yes" and confirm by pressing enter

    Xiaomi Mi Robot Vacuum seit 04/2018 (FW: 3.5.0_003476)

    Xiaomi Mi Home Sicherheitskamera 360° 1080p (FW: 3.5.1_0217)

    Fuxtec FB144 seit 04/2019 (FW: Fuxtec 1.2-6)

  • I've done that already. Now I am a little bit desperate :(

    Does anybody know how to reset home address?

  • manual section 5.6: adress setting

    to reset adress

    - select "set" and enter it by pressing green enter key

    - select "function" and enter it by pressing enter key

    - select "adress" and enter it by pressing enter key

    - press the green enter button on charging station

    - mower will receive the correct adress, press "yes" to confirm

    Xiaomi Mi Robot Vacuum seit 04/2018 (FW: 3.5.0_003476)

    Xiaomi Mi Home Sicherheitskamera 360° 1080p (FW: 3.5.1_0217)

    Fuxtec FB144 seit 04/2019 (FW: Fuxtec 1.2-6)

  • Tried few times and no improvement...

    I posted a picture few posts above with address that I have now...

  • Out of nowhere today it just started working 8|

    I was testing it and grass was a little bit wet so I washed it with a water hose, left on charging station overnight and in the morning everything was ok ! Maybe some sensor was blocked/dirty, I don't know :/

    Thanks to everyone who tried to help ! :thumbup: